Your fingerprint browser shows a green connection indicator in the top-right corner, the latency reading looks normal, yet when you open an IP lookup page it still reports your home broadband's public address. The settings were saved, so why hasn't the exit IP changed at all?
That doesn't necessarily mean the line is broken. A successful connection only proves the browser can talk to the line's server; it doesn't prove your web requests are actually leaving through the network exit you expect. The most direct way to confirm the setup took effect is to check the IP that outside websites actually see.

Start by checking whether the browser window was restarted. Some fingerprint browsers load their network parameters when a window launches, so if you only refreshed the page after editing the configuration, the previous connection settings may still be in effect. Close the window completely, open it again, and run the check.
Next, review your routing rules. Some browsers and network tools let you send certain sites through a direct connection. If the IP lookup site happens to be on that direct list, you'll see your local public IP.
It's also worth checking whether other traffic-forwarding software is running on the machine. Different programs can modify system routes or network settings at the same time, and the browser's traffic may end up taking a path you didn't intend.
If all of that looks right, move on to IPv6 and WebRTC. On networks that support both IPv4 and IPv6, a changed IPv4 exit doesn't mean every connection is being routed the way you set it.
Before troubleshooting, open ToDetect in a browser environment where the target line is not enabled, and record the current public IPv4, IPv6, DNS, and WebRTC results as a baseline.
Then enable the line you configured, close the original browser window, and open a new one to load ToDetect again.
Watch whether the exit IP changed and whether the detected address matches the line you expected. If IPv4 has changed but IPv6 still shows your original public address, check whether the line supports IPv6 and whether the browser is reaching sites over IPv6 directly.
DNS is worth checking on its own. A correct exit IP paired with DNS requests still handled by the local network may mean resolution traffic isn't taking the expected path. That said, a DNS server sitting in a different location from the exit IP isn't automatically a leak—it depends on the resolver and your specific network setup.
For WebRTC, check whether it exposes a real public IP you didn't expect. If it only shows a private address or an mDNS-obfuscated one, that alone doesn't prove your real public IP has leaked.
| What you see | Likely cause | Where to look |
|---|---|---|
| Exit IP never changes | Network settings didn't take effect, or the site is set to connect directly | Restart the browser window; check the line configuration and routing rules |
| IPv4 changed, IPv6 still shows a local address | IPv6 traffic isn't going through the expected line | Check whether the line supports IPv6, and review the browser's IPv6 settings |
| Exit IP looks right, DNS results look off | DNS requests may still be handled by the local network | Review secure DNS settings and how the system resolves DNS |
| WebRTC shows your original real public IP | WebRTC may be bypassing the expected line | Check the browser's WebRTC network policy and related settings |
| Different IP check sites report different IPs | They're checking different IP protocols or network paths | Compare IPv4 and IPv6 separately, then read the DNS and WebRTC details together |
| IP changed, but time zone, language, and location don't match | Browser environment parameters weren't updated to match | Check time zone, language, and other fingerprint parameters to confirm the environment matches what you intended |
One caveat: a DNS server in a different location, or a private address showing up in WebRTC, doesn't necessarily mean your real IP has leaked. Read the specific results before drawing conclusions, so you don't chase false alarms.
Yes, but the two are answering different questions. An IP check reflects your network exit, while a browser fingerprint check looks at environment parameters such as Canvas, WebGL, fonts, screen resolution, time zone, and language.
For example, the detected exit IP is located in Germany while the browser's time zone is still Beijing time. That isn't a real IP leak—it just means the network location and the browser environment don't line up.
On top of that, even after the exit IP changes, some fingerprint parameters can stay identical. So you can't assume the whole browser environment has changed just because the IP did.
In ToDetect, look at network results and fingerprint results separately, so you don't end up mixing two different kinds of problems together.
Run a full check once right after you finish configuring a line. After that, re-test whenever you switch lines, change network settings, or update the browser engine.
If a check comes back abnormal, keep the results from before and after the change and compare them item by item, rather than changing several settings at once. That makes it much easier to pin down which step actually affected the network exit.
A fingerprint browser reporting a successful connection is only a starting point. Whether the IP really changed—and whether your real address slipped out—comes down to the actual test results.
Compare exit IP, IPv6, DNS, and WebRTC in ToDetect, then read those results alongside browser fingerprint data, and you'll have a much clearer path to the root of the problem.
Efficiently solve multi-account management, environment isolation, and account security